Hammer Crusher

Hammer Crusher Category

The Yifan mechanical hammer crusher can be divided into the drying hammer crushers and ring hammer crusher

About Drying Hammer Crusher


SMH series hydraulic cone crusher adopting world advanced technology is designed and made through to be the crusher of world advanced level. it is widely used in metallurgical, architectural, water and electricity, traffic, chemical, architectural material industries. It is suitable for crushing varies of mid hard and above mid hard ores and rocks.
 

Drying Hammer Crusher
Drying Hammer Crusher

SMH  Series Drying Hammer Crushers is suitable for crushing and drying soft or nonabrasive materials, eg:gypsum, chalk, clay, slurry, filtered cake, etc. It can break up, dry and calcine industrial byproduct plaster, flue gas desulfurized gypsum. This equipment is of high efficiency and low energy consumption. It has the function of breaking up and crushing the materials while drying them. The rotary totor breaks up the materials, hot blast dries them, and air flow takes the crushed and dryed materials into separation chamber. Afterwards, fine powder is separated in cyclone, while coarse particles goes back to the hammer crusher and crushed again.

In gypsum board industry, the rotor on DSJ Series Drying Hammer Crusher can break up and throw the desulfurized gypsum slag, whose water content is no more than 12%. During this process, the gypsum slag exchanges the heat with the intake hot air of 550℃, and then the max water content of the material is 1%, which goes into riser from outlet duct and then hot air takes the material into the next process. This machine can also be used to dry and crush filtered cake in cement industry and calcium carbide slag in environmental protection.

SMH  Series Drying Hammer Crushers adopt reasonable and reliable process technology, high-quality material and advanced automated processing equipment, which ensures the reliable and steady operation, and convenient maintenance. Each environmental indicators of this equipment are in line with the requirements of the country.

Desulfurized gypsum slag used to be processed through the landfill, which seriously pollutes the environment and uses the farmland. Nowadays, the desulfurized gypsum slag can be used as construction gypsum powder, after being processed by this machine. What's more, its performance is better than that of natural gypsum. It is high-quality raw material to produce gypsum board.


Successful project:

Gypsum board production line in Taicang Beijing New Building Material Co.,Ltd. attached to China National Building Material Group Corporation.

 

About Ring Hammer Crusher:

PCH series ring hammer crusher is to crush the material by the high-speed rotating hammers. This ring hammer crusher has the characteristics of simple structure, large crushing ratio, and high production efficiency. It can be used to crush the dry or wet materials. It is used to crush the mid-hard and low-abrasive materials, whose compressive strength is not more than 100MPa, and whose moisture percentage is not more than 15%. The common materials are coal, salt, chalk, gypsum, limestone, and so on. It is also used to crush the wood pieces, paper, and asbestos cement waste, which are fiber-structural, elastic and strong tenacity. Ring hammer crusher is not only used in aggregate or sand production line, but also in mineral selection process instead of cone crusher.
 

Ring Hammer Crusher
Ring Hammer Crusher

PCH Series Ring Hammer Crusher is used to crush coal, especially brittle materials, like gangue, coke, slag, red sandstone, shale, loose limestone, etc. The compressive strength of the material does not surpass 15%. It has the following features: energy-saving, fine output size, higher efficiency, and lower noise, less dust pollution and so on.

Application of PCH Ring Hammer Crusher:

DSJ Series Drying Hammer Crushers adopt reasonable and reliable process technology, high-quality material and advanced automated processing equipment, which ensures the reliable and steady operation, and convenient maintenance. Each environmental indicators of this equipment are in line with the requirements of the country.

Working Principle:

PCH series ring hammer crusher is an impact rotor-type crusher with hammer ring. The materials are impacted and crushed by the high-speed rotating hammers after entering the chamber. The crushed materials get the impetus energy from the hammers, and then they will impact on the crushing plate. After the secondary crushing process, the materials fall on the sieve plate. Then the materials are crushed again after being sheared, extruded, and grinded, and then drop out. Unbroken matters enter the metal collector, which are cleaned periodically.

Thank you for your interest in YIFAN. Please use any of the methods below to get in touch with us.  
Add: The Middle of Zhengyuan Road, Xingyang Eastern Development Zone.
zip:450100
E-mail:yifanseo@yfmac.com
MSN On line: yifancrusher@yahoo.cn             
ICQ: 639607958 QQ: 2502761202
Tel: +86-371-64628852 Fax: +86-371-64628872
The article by Vibrating Screen: http://www.vibratingscreens.org, please indicate the source , little effort , thank you .
 

  • Name:
  • Tel:
  • E-mail
  • Message